Looking for a 3D printer extruder? Find the best-selling 3D printer extruders and extruder parts at Amazon in our list.
Extruders are undoubtedly the most important components of any FDM 3D printer. There are two common types of 3D printer extruders.
The extruders in this list were selected from the Amazon Bestsellers list for the 3D printer extruders category. Please note that there’s no quality-ranking in this list.
|Wahhing Heater Block Cotton|
|PTFE Teflon Bowden Tube|
|3Doodler Nozzle Set|
|Micro Swiss All Metal Hotend||Direct||n/a|
|Signstek Ceramic Cartridge Heater|
|BIQU Aluminum Heater Block (5 PCS)||Heater Block|
|E3D All-metal v6 Hotend Full Kit||Hotend Direct||1.75 mm|
|EAONE All-Metal Hotend|
|EasyULT 6PCS Nozzle Bundle|
|RepRap Champion 2M PTFE Teflon Tube|
|RepRap Champion Metal J-Head V6 Hotend||Bowden Hotend||1.75 mm|
|PTFE Teflon Bowden Tube|
|Micro Swiss MK10 All Metal Hotend Kit|
|Witbot All-Metal Hotend|
|KKmoon DIY Hot End Kit|
|MakerBot Smart Extruder+||Direct||MakerBot PLA only|
What is this 3D printer extruder? This 14 piece bundle contains six 30 mm long 1.75 mm extruder tubes and six 0.4 mm brass nozzles. It is compatible with all printers and hotends that have 1.75mm diameter.
What is this 3D printer extruder part? The Wahhing Heater Block Cotton is 85mm x 20mm x 2mm. You will achieve a much better temperature consistency by insulating the heating block of the extruder with this. Please note that you don’t go over (or hit) 300°C with this!
What is this 3D printer part? This is a tube for 1.75mm filament. It is normally used with a PC4-M6 type push-in fitting. Remember to not let your hotend get hotter than 260°C!
What is this 3D printer part? This set of 3D pen nozzles contains storage for six changeable, new and improved nozzles. Added, there’s a smoothing tool for your creations. The set will help you control the flow of the plastic and with that the variety of your designs and gives you the opportunity to store the nozzles safely.
What is this 3D printer extruder? This is an all metal hotend designed by Micro Swiss to deliver more consistent melt chamber control. This is achieved by the two-layer stainless steel and aluminum heat sink instead of using a PTFE lined hotend. It’s one of the most popular choices when it comes to quality all-metal hotends.
What is this 3D printer part? This part is made especially for the for Prusa Mendel type 3D printers.
What is this 3D printer part? This is a pack of five 3D printer heater blocks. They are made out of solid aluminum. Without one of these, your 3D printers nozzle will not heat up. This is where the filament melts as it passes through the extruder tube. These are designed for MK7 and MK8 extruders.
What is this 3D printer extruder? The E3D v6 HotEnd Full Kit is a true workhorse. The 1.75 mm direct version of this hotend is specially designed to contain a PTFE liner extending from the extruder. This enables near full constraint on the filament between the drive gears of the extruder to the hotend. When using flexible and soft materials, this kind of control over the filament is very important.
The nozzle can reach temperatures of up to 300°C without exposing the contained PTFE liner to extreme temperatures. A thermistor upgrade can allow the hotend to reach temperatures of even 400°C. Equipped with these features, this unit can truly handle any filament you throw at it.
What is this 3D printer extruder? This set includes 5 extruder brass print heads and 5 stainless steel nozzle throats for the E3D V6 hotends. It can reach temperatures up to 280° but should be used at 240°C for long terms. Buy a set and share with your friends.
What is this 3D printer part? It is a bundle with 6 pieces of 0.4 mm brass nozzles suitable for 1.75 mm MK8 extruders. These nozzles are not suitable for abrasive 3D printing materials.
What is this 3D printer extruder part?This 2m teflon tube is made for 1.75 mm filament. It also comes with two PC4-M6 push-in tube fittings.
What is this 3D printer extruder part?This is a clone of the E3D V6 hotend. It boasts the same capabilities as the real thing at a fraction of the cost. It is compatible with Bowden style feeders. The hotend boast being capable of reaching high enough temperatures to print materials like nylon and polycarbonate. A 1-meter long piece of PTFE tubing is included.
What is this 3D printer extruder? This HICTOP model is an upgraded replacement for the aluminum MK8 extruder. It can be used on all types of 1.75mm filament printers. It has a brass extruder drive gear and a 35 mm long teflon intake to keep the filament away from Z-screw rod.
What is this 3D printer extruder part? This is a tube for 1.75mm filament and normally used with a PC4-M6 type push-in fitting. Again, remember to not let this tube get hotter than 260°C.
What is this 3D printer extruder? With this hotend, you can reach up to 280°C if you replace the thermistor with a thermocouple. It is compatible with the E3D V6 1.75mm / 0.4mm and works with PLA and ABS. The hotend also contains a 12V 40W heater, a 12V high-speed fan and a NTC 3950 pre-wired thermistor.
What is this 3D printer extruder? This Hotend kit is compatible with the FlashForge Creator Pro, the FlashForge Creator X, FlashForge Dreamer, Dremel Idea, Builder PowerSpec 3D, Pro PowerSpec 3D X, Wanhao Duplicator 4S, Wanhao Duplicator 4X, Wanhao i3 which makes it very practical since you can use it with several different printers. Also, it is an all-metal hotend which makes it easier to print at high temperatures.
What is this 3D printer part? This Hotend is made from brass. Its input diameter is 1.75mm, the opening is 0.4mm wide. This extruder nozzle comes in the size 13mm x 6mm.
What is this 3D printer part? This part is compatible with the V6 RepRap 3D Printer. Its inner diameter is 2mm and supposed to be used with 1.75mm filament. Also, it has an all metal heat break (for the V6) and comes in a pack of five.
What is this 3D printer part? This DIY hotend kit is supposed to help you with a damaged Anet A2 & A3-S A6 & A8. It comes with a pre-wired NTC3950 thermistor, a 6 x 20mm cartridge heater and is compatible with 1.75 mm filament. The extruder throat is 6mm diameter (with external thread) and 30mm long.
What is this 3D printer extruder? The MakerBot Smart Extruder+ is the updated version of its predecessor, the MakerBot Smart Extruder, which was notoriously unreliable. MakerBot took a lot of time and effort to improve this essential 3D printer component.
After over a total of 160,000 cumulative hours of in-house testing, MakerBot has significantly improved the extruder. The component offers consistent performance with many features on top of that. A sensor system feeds information straight to your MakerBot software. This lets you know the state your extruder is in. Other sensors help with the calibration of the build plate or pause the printing process if a filament jam is detected, which will allow the user to resume the print when the problem has been fixed. A modular design allows for quick and easy removal and installation of the extruder.
This 3D printer extruder is compatible with the current line-up of MakerBot Replicator and MakerBot ReplicatorMini. It comes with a 6-month warranty.
License: The text of "Best-Selling 3D Printer Extruders and Extruder Parts at Amazon" by All3DP is licensed under a Creative Commons Attribution 4.0 International License.
Subscribe to updates from All3DP
You are subscribed to updates from All3DP
You can’t subscribe to updates from All3DP. Learn more…