Featured image of Tinkercad Tutorial – 5 Easy Steps for Beginners
Start Tinkering

Tinkercad Tutorial – 5 Easy Steps for Beginners

Picture of Dibya Chakravorty
by Dibya Chakravorty
Jul 8, 2017

In this Tinkercad tutorial for beginners, we will show you in just five easy steps how to create 3D models in Tinkercad. You can do it!

Tinkercad Tutorial – 5 Easy Steps for Beginners

Tinkercad Tutorial: Introduction

For this Tinkercad tutorial, we chose to design a wrench. It’s a familiar and simple shape, and is useful in daily life. If you haven’t seen a wrench before, it is used by mechanics for tightening nuts and bolts. Here’s what one looks like:

We will use this real life wrench as a template for this Tinkercad tutorial
We will use this real life wrench as a template for this Tinkercad tutorial

for the purpose of this Tinkercad tutorial and to better acqaint you with the site’s interface, we will split the design of the wrench into five simple steps. These cover the basics of 3D modeling as we go. At the end of the Tinkercad tutorial, you will not only be able to design the wrench yourself but will also have the skills to design any simple 3D model that you wish.

For those who prefer their directions a little more watch-ey, and a lot less read-ey, you can check out our YouTube version of this Tinkercad tutorial, embedded below.

Let’s get started.

Tinkercad Tutorial Step 1: Create a Tinkercad Account and Create a New Project

Using Tinkercad is easy because it runs in the browser. This means you don’t need to download or install any software. You simply need to create a Tinkercad account to get started. To get a free account, visit Tinkercad and sign up.

At the end of the signup process, you will be welcomed by the Tinkercad tutorial screen. You can skip the tutorial for now by closing it.

Instead, go to the home page (shown below), and click the “Create new design” button.

Creating a new project on Tinkercad
Tinkercad Tutorial: Creating a new project on Tinkercad

This will open up a new project page, which looks as follows.

The beautiful Tinkercad interface
An empty Tinkercad workplane for you to tinker with

This is the Tinkercad interface.

  1. Notice the blue plane at the center of the page (marked 1). This plane is known as the workplane. This workplane is the 3D analog of a Photoshop or GIMP canvas. We will do all our designing on this workplane.
  2. Notice the panel with geometric shapes on the right (marked 2). This panel contains the basic building blocks for everything we will design.
  3. Notice the menu items on the top bar (marked 3 and 4). We will use these menu items to perform important operations like aligning, merging, etc.
  4. Finally, right click and drag your mouse to change the 3D perspective of the workplane. Scroll up and down to zoom in and out.

Tinkercad Tutorial Step 2: Design the Ring

Now that we have familiarized ourselves with the Tinkercad interface, we will start designing the wrench.

Tinkercad Tutorial 2.1: Divide and Conquer

A key principle in 3D modeling is “divide and conquer.” It means that when modeling a  complex real world object, we should divide it into smaller geometric shapes and then design these smaller units individually. In the final step, we should put these small units together. This makes modeling a complex object easy.

Applying this principle to the wrench, we divide it into three basic units:

  1. The ring
  2. The handle
  3. The jaw
The different parts of a wrench - the ring, the handle and the jaw
The different parts of a wrench – the ring, the handle, and the jaw

We will start by designing the ring.

The ring of a wrench can be approximated by a solid circular disk with a hollow circular area in the middle.

Tinkercad Tutorial 2.2: Creating the Solid Circular Disk

To create this shape, we will first drag a cylinder from the Basic Shapes panel to the workplane. You will notice that the cylinder has five white square handles, four of which are on the plane and one of which is above the cylinder.

The white handles let users change the dimension of a Tinkercad shape
The white handles let users change the dimension of a Tinkercad shape

The four handles on the plane can be used for adjusting the cylinder’s length and width. We want our ring to have a diameter of 25mm. Therefore, drag the square handles till the cylinder has a length and width of 25mm.

The one above the cylinder can be used for adjusting its height. We want our wrench to have a height of 4mm. Therefore, click the handle with the left mouse button and drag it down till the cylinder has a height of 4 mm.

We changed the dimensions of the Tinkercad cylinder to make a disk with diameter 25mm and height 4mm
We changed the dimensions of the Tinkercad cylinder to make a disk with diameter 25mm and height 4mm

Tinkercad Tutorial 2.3: Creating the Circular Hole

We are making progress: we now have the solid disk. But how do we make the circular hole in the middle?

Tinkercad operates on the principle of Boolean design, which means it allows you to subtract objects to create hollow areas or add objects to join two shapes. In this case, we will need to use subtraction to create the circular hole in the middle of our ring.

First, drag another cylinder to the workplane. Use the white handles on the plane to adjust the length and width of the cylinder to 12.5mm, which is the diameter of the hole that we want to create.

Now comes the fun part. With this cylinder selected,  choose “Hole” in the panel on the upper right corner (marked by the blue rectangle in the image). This prepares this shape to be subtracted out.

A cylinder shaped hole
A cylinder shaped hole

Tinkercad Tutorial 2.4: Aligning the Hole and the Disk

Next, we need to bring this cylinder shaped “hole” in the middle of the solid disk. We will use the alignment tool in the top menu to achieve this.

To use the alignment tool, select the cylinder shaped hole by left clicking. Now press the shift button and select the solid disk. If you do this correctly, you will see that both objects are now simultaneously selected and highlighted.

"<yoastmark

Press the Align button on the top menu (marked with a blue rectangle). Black alignment handles will appear on the workplane. Click on the appropriate handles (also marked with blue rectangles) to bring the solid cylinder in the middle of the solid disk.

The black alignment handles help align two shapes in Tinkercad
The black alignment handles help align two shapes in Tinkercad
"<yoastmark

Tinkercad Tutorial 2.5: Grouping the Cylinder Shaped Hole and the Disk to Create the Ring

When the two shapes are aligned, press the “Group” button in the top menu (marked in the blue rectangle). The Group button essentially joins two shapes together. However, if one of the shapes is a hole, then it creates a hollow area instead.

The Group button merges two Tinkercad shapes
The Group button merges two Tinkercad shapes

Voila! We now have a beautiful ring and have finished the first step in creating our wrench.

A beautiful ring on the workplane
A beautiful ring on the workplane

We learned quite a bit in this section. We learned how to change the dimensions of basic shapes, how to create holes, how to align shapes and finally how to group (or merge) two shapes together. The good thing is, these skills constitute 90 % of what you need to know to design 3D objects in Tinkercad. The next steps will involve the same skillset or small variations thereof.

Tinkercad Tutorial Step 3: Design the Handle

The handle is probably the easiest part of the wrench.

The handle is rectangular. So we simply drag a box from the basic shapes panel into the workplane.

We will use a box shape to create the handle of the wrench
We will use a box shape to create the handle of the wrench

Using the white handles on the plane, we set the length of the box to 100mm, the width of the box to 10mm.

By dragging the white handle on the top of the box, we set the height to 4mm so that it matches the height of the solid ring.

"<yoastmark

That’s it. The handle is ready to go.

Tinkercad Tutorial Step 4: Design the Jaw

The design of the jaw is very similar to the ring that we designed in Step 2 of this Tinkercad tutorial. Basically, the jaw is also a circular disk, but with a polygonal hole carved out at an angle.

Top view of the jaw that we are going to design
Top view of the jaw that we are going to design

As with the ring, we first need to create a circular disk of diameter 30mm and height 4mm. We have done this before, so you should be able to do this step without much problem.

To create the jaw, we first create a disk with diameter 30mm
To create the jaw, we first create a disk with diameter 30mm

To create the jaw like shape, we will use the basic shape called “Polygon”. Drag the Polygon to the workplane, select it, and turn it into a hole (as we did in Step 2). Now position the Polygon and adjust its dimensions.

A polygon shaped hole is used to create the jaw like shape
A polygon-shaped hole is used to create the jaw like shape

If you are planning to use the wrench from this Tinkercad tutorial for household repairs, you can choose the dimension of the corresponding nut and bolt. We will use a 15mm jaw and adjust the width of the polygon to 15mm accordingly.

We set the width of the polygon to 15 mm
We set the width of the polygon to 15 mm

Make sure the polygon is aligned with the center of the disk by using the alignment tool.

Align the polygon and the disk
Align the polygon and the disk

It’s time to do some subtraction magic. Select both the polygonal hole and the disk by holding shift and selecting both. When they are selected simultaneously, press the Group button on the top menu (marked in the blue rectangle).

"<yoastmark

Congratulations! You have successfully created the jaw!

"<yoastmark

Tinkercad Tutorial Step 5: Putting it All Together

In this Tinkercad tutorial, we have so far designed the individual parts of the wrench. Now it is time to put it all together. Exciting, isn’t it?

Tinkercad Tutorial 5.1: Merging the Handle and the Ring

First, position the handle so that it goes a little bit into the body of the ring.

The handle should go just a little bit inside the ring
The handle should go just a little bit inside the ring

Select the handle and the ring together and align it so that the handle aligns with the center of the ring. Now press the Group button. This should merge the handle and the ring into one continuous unit. Notice that the merged unit now has a single color instead of two colors.

"<yoastmark

Tinkercad Tutorial 5.2: Rotating the Jaw

The jaw is facing the wrong direction. We need to fix that by rotating it. To rotate the jaw, first select it. You will see that in addition to the white square handlesfrom before, there are three curved handles with double arrows (marked in blue rectangles).

"<yoastmark

These are the rotation handles. Use the X-Y plane rotation handle to rotate the jaw so that it faces the direction shown in the figure below.

The jaw should make a small angle wrt to the handle
The jaw should make a small angle wrt to the handle

Tinkercad Tutorial 5.3: Merging Everything Together

Now let’s add the jaw to the previously merged unit. The procedure is more or less the same as what we used for adding the handle and the ring.

First, drag the jaw and position it so that the handle goes a little bit inside the body of the jaw. Select the jaw and the merged unit simultaneously and align them so that the handle aligns with the center of the jaw.  Press the Group button to merge them.

A complete wrench on the workplane
A complete wrench on the workplane

You should now have a complete wrench on the workplane. Isn’t that awesome?

Tinkercad Tutorial 5.4: Changing Colors

You might want to change the color of the wrench because an orange wrench just doesn’t look right. A wrench should be gray, right?

We pick a dark grey for the wrench using the color menu
We pick a dark gray for the wrench using the color menu

To change the color, select the wrench and press the “Solid” button on the upper right corner panel (marked by the blue rectangle).  You should see a selection of colors at this point. Let’s choose a dark gray.

And there you have it!  A perfect wrench on the workplane!

Finish line - a beautiful grey wrench on the workplane
Finish line – a beautiful gray wrench on the workplane

You have just designed a beautiful gray 3D printable wrench. That’s no mean feat. Also, you now also know enough about Tinkercad to design any other 3D printable model that your heart desires.

Optional Step After Finishing This Tinkercad Tutorial: 3D Print Your Model

Who doesn’t want to see their creations come to life? If you have a 3D printer, you can print out the wrench, use it in your daily life and show your friends what you have made.

If you don’t have a 3D printer, you can submit your design to 3D printing services, who will print it and ship the model to you. To get the best price, you can use All3DP’s free price comparison service.

Tinkercad makes both of these workflows easy.

  1. If you have a 3D printer (or have access to one), select Export and then choose the .STL or .OBJ file format. This will download the 3D printable file of the wrench on your computer.
  2. If you want to have your wrench from this Tinkercad tutorial printed by a printing service, go to the home page and then click on your design. You will find an option called “Order a 3D print” (marked with the blue rectangle). Click the option and select one of Tinkercad’s 3D printing partners.
  3. If you want to use the wrench from this Tinkercad tutorial, you should 3D print it with 100 percent infill and in a material that‘s durable.
Press the button marked with the blue rectangle to order a 3D print on Tinkercad
Press the button marked with the blue rectangle to order a 3D print on Tinkercad

That’s it for now. We hope you enjoyed this Tinkercad tutorial. If you face any difficulty or confusion when following the instructions, let us know in the comments, and we will try to help you out.

Recommended for you